The AGD Signature Range nuts, bolts and washers provide fixings for compatible rainwater system assemblies. This listing is supplied in a pack size of 100.

Use the specified fixing type and size for the joint or component being assembled. Confirm the pack contents, dimensions and suitability with AGD where these are required for a particular installation.

Where the system uses a bolted and sealed joint, apply the specified sealant as well as the mechanical fixings. Follow the installation instructions for tightening and joint preparation.

The AGD Signature Range Belle Vue Corner cast aluminium hopper collects incoming rainwater and channels it into the downpipe below. The corner version of the Belle Vue design is intended for a corner position. Check the building corner and incoming pipe arrangement before selecting it.

Cast aluminium provides the definition associated with traditional hopper heads while offering lower weight than cast iron. Coordinate the hopper with the surrounding guttering and downpipes for a consistent finish.

Choose Milled for an uncoated aluminium finish, or one of the 11 listed RAL powder-coated colours to coordinate with your roofline.

Confirm the hopper dimensions, outlet size and connection arrangement with AGD before ordering. Allow for the incoming discharge and keep the hopper accessible for regular debris removal.

The AGD Signature Range Cranford Hopper cast aluminium hopper collects incoming rainwater and channels it into the downpipe below. The Cranford design adds a decorative focal point where incoming rainwater enters the downpipe.

Cast aluminium provides the definition associated with traditional hopper heads while offering lower weight than cast iron. Coordinate the hopper with the surrounding guttering and downpipes for a consistent finish.

Choose Milled for an uncoated aluminium finish, or one of the 11 listed RAL powder-coated colours to coordinate with your roofline.

Confirm the hopper dimensions, outlet size and connection arrangement with AGD before ordering. Allow for the incoming discharge and keep the hopper accessible for regular debris removal.

The AGD Signature Range Box Hopper cast aluminium hopper collects incoming rainwater and channels it into the downpipe below. The box design offers a straightforward geometric form for an orderly transition into the downpipe.

Cast aluminium provides the definition associated with traditional hopper heads while offering lower weight than cast iron. Coordinate the hopper with the surrounding guttering and downpipes for a consistent finish.

Choose Milled for an uncoated aluminium finish, or one of the 11 listed RAL powder-coated colours to coordinate with your roofline.

Confirm the hopper dimensions, outlet size and connection arrangement with AGD before ordering. Allow for the incoming discharge and keep the hopper accessible for regular debris removal.

The AGD Signature Range Belle Vue Large cast aluminium hopper collects incoming rainwater and channels it into the downpipe below. This is the larger Belle Vue design, providing a more substantial architectural feature on the elevation. Confirm the dimensions against the available wall space.

Cast aluminium provides the definition associated with traditional hopper heads while offering lower weight than cast iron. Coordinate the hopper with the surrounding guttering and downpipes for a consistent finish.

Choose Milled for an uncoated aluminium finish, or one of the 11 listed RAL powder-coated colours to coordinate with your roofline.

Confirm the hopper dimensions, outlet size and connection arrangement with AGD before ordering. Allow for the incoming discharge and keep the hopper accessible for regular debris removal.

The AGD Signature Range Belle Vue cast aluminium hopper collects incoming rainwater and channels it into the downpipe below. The Belle Vue design provides a decorative collection point for traditional rooflines and elevations.

Cast aluminium provides the definition associated with traditional hopper heads while offering lower weight than cast iron. Coordinate the hopper with the surrounding guttering and downpipes for a consistent finish.

Choose Milled for an uncoated aluminium finish, or one of the 11 listed RAL powder-coated colours to coordinate with your roofline.

Confirm the hopper dimensions, outlet size and connection arrangement with AGD before ordering. Allow for the incoming discharge and keep the hopper accessible for regular debris removal.

The AGD Signature Range cast aluminium deep flow gutter collects roof water in a traditional cast section. The deeper rounded channel offers a distinct traditional profile for projects requiring this gutter shape. The roof area and outlet arrangement should determine the final drainage specification.

Cast aluminium provides a lighter alternative to cast iron while retaining the character of traditional rainwater goods. This is a cast gutter system with spigot joints, assembled using the specified bolts and sealant.

Supplied in 1.83m (6ft) lengths. Contact AGD to confirm the profile dimensions for your project before ordering. Choose Milled for an uncoated aluminium finish, or one of the 11 listed RAL powder-coated colours to coordinate with your roofline.

Use matching cast-system fittings and supports, and check the profile against any existing guttering before ordering for a repair or extension. For heritage projects, confirm that the proposed profile meets the project's requirements.

The AGD Signature Range cast aluminium ogee gutter collects roof water in a traditional cast section. The decorative ogee front adds a shaped detail to the roofline, making it suitable for projects where the gutter forms a visible architectural feature.

Cast aluminium provides a lighter alternative to cast iron while retaining the character of traditional rainwater goods. This is a cast gutter system with spigot joints, assembled using the specified bolts and sealant.

Supplied in 1.83m (6ft) lengths. Available gutter sizes: 100x75mm, 112x100mm and 150x100mm. Choose Milled for an uncoated aluminium finish, or one of the 11 listed RAL powder-coated colours to coordinate with your roofline.

Use matching cast-system fittings and supports, and check the profile against any existing guttering before ordering for a repair or extension. For heritage projects, confirm that the proposed profile meets the project's requirements.

The AGD Signature Range cast aluminium non-beaded half round gutter collects roof water in a traditional cast section. The plain half round profile gives a simpler traditional appearance, with an un-beaded edge for projects where that detail needs to be retained.

Cast aluminium provides a lighter alternative to cast iron while retaining the character of traditional rainwater goods. This is a cast gutter system with spigot joints, assembled using the specified bolts and sealant.

Supplied in 1.83m (6ft) lengths. Available gutter sizes: 100mm. Choose Milled for an uncoated aluminium finish, or one of the 11 listed RAL powder-coated colours to coordinate with your roofline.

Use matching cast-system fittings and supports, and check the profile against any existing guttering before ordering for a repair or extension. For heritage projects, confirm that the proposed profile meets the project's requirements.

The AGD Signature Range cast aluminium beaded half round gutter collects roof water in a traditional cast section. The rounded channel and beaded rim create a traditional roofline detail, making this profile a useful option for projects seeking the appearance of period rainwater goods.

Cast aluminium provides a lighter alternative to cast iron while retaining the character of traditional rainwater goods. This is a cast gutter system with spigot joints, assembled using the specified bolts and sealant.

Supplied in 1.83m (6ft) lengths. Available gutter sizes: 112mm and 125mm. Choose Milled for an uncoated aluminium finish, or one of the 11 listed RAL powder-coated colours to coordinate with your roofline.

Use matching cast-system fittings and supports, and check the profile against any existing guttering before ordering for a repair or extension. For heritage projects, confirm that the proposed profile meets the project's requirements.

The AGD Signature Range moulded ogee Fast-Fit jointing clip connects adjoining sections of the matching gutter system. It forms part of the joint assembly between lengths and compatible fittings.

The clip follows the moulded ogee Fast-Fit section to provide the appropriate joint interface. Use it with the specified sealant and joint preparation method for this system.

Gutter sizes: 100x76mm, 125x100mm, 150x100mm and 200x150mm. Choose Milled for an uncoated aluminium finish, or one of the 11 listed RAL powder-coated colours to coordinate with your roofline.

Match the clip to the gutter size and jointing arrangement. Follow the profile-specific instructions for assembly and expansion allowance; a clip alone does not replace the required sealing work.

The AGD Signature Range moulded ogee Fast-Fit rise and fall bracket allows the gutter height to be adjusted during installation. It helps establish the required alignment and fall where the support positions need individual adjustment.

Designed for the matching moulded ogee Fast-Fit section, this bracket provides an alternative support arrangement for layouts that need more control over the gutter level.

Gutter sizes: 100x76mm, 125x100mm, 150x100mm and 200x150mm. Choose Milled for an uncoated aluminium finish, or one of the 11 listed RAL powder-coated colours to coordinate with your roofline.

Choose the correct gutter size and confirm that the fixing arrangement is suitable for the building. Follow the installation guidance for spacing and adjustment.

The AGD Signature Range moulded ogee Fast-Fit rafter bracket provides a support option where the gutter needs to be mounted from the rafters. It is useful where a fascia fixing arrangement is unsuitable.

Select Top Fix for fixing from above or Side Fix for attachment to the side of the rafter. Choose the version that suits the accessible fixing face and the required gutter position.

Gutter sizes: 100x76mm, 125x100mm, 150x100mm and 200x150mm. Choose Milled for an uncoated aluminium finish, or one of the 11 listed RAL powder-coated colours to coordinate with your roofline.

Match the bracket to the moulded ogee Fast-Fit gutter size. Check the rafter arrangement, roof edge clearance and required fixing positions before ordering.

The AGD Signature Range moulded ogee Fast-Fit fascia bracket supports the matching gutter from the fascia board. Its profile follows the gutter section to keep the run securely positioned beneath the roof edge.

Choose the bracket size to match the moulded ogee Fast-Fit gutter. Suitable support positions help maintain the intended alignment and fall along the installation.

Gutter sizes: 100x76mm, 125x100mm, 150x100mm and 200x150mm. Choose Milled for an uncoated aluminium finish, or one of the 11 listed RAL powder-coated colours to coordinate with your roofline.

Use fixings appropriate for the fascia and follow the profile-specific installation guidance for bracket spacing and support around fittings.

The AGD Signature Range moulded ogee Fast-Fit stop end closes an open end of the gutter run. It provides the matching terminal fitting where the gutter finishes at the edge of the roofline.

Made for the moulded ogee Fast-Fit profile, this aluminium component completes the shape of the gutter at the end of the run. Left-hand and right-hand options are available; choose the hand required by your layout.

Gutter sizes: 100x76mm, 125x100mm, 150x100mm and 200x150mm. Choose Milled for an uncoated aluminium finish, or one of the 11 listed RAL powder-coated colours to coordinate with your roofline.

Fit and seal the stop end in accordance with the system instructions. Check the completed joint as part of the installation's water test.

The AGD Signature Range moulded ogee Fast-Fit running outlet creates the connection between the gutter run and the downpipe. It collects water from the adjoining gutter sections and directs it into the selected outlet.

Choose the gutter size first, then select an available round, square or rectangular outlet to suit your downpipe. Outlet choices depend on the gutter size and are shown in the product options.

Gutter sizes: 100x76mm, 125x100mm, 150x100mm and 200x150mm. Choose Milled for an uncoated aluminium finish, or one of the 11 listed RAL powder-coated colours to coordinate with your roofline.

Check both the gutter connection and downpipe outlet dimensions before ordering. The number and position of outlets should be chosen to suit the roof area and drainage layout.

The AGD Signature Range moulded ogee Fast-Fit gutter angle takes the gutter run around a building corner while maintaining the matching profile. It connects straight sections where the roofline changes direction.

These aluminium corner fittings are available in internal and external 90° and 135° options. Choose the angle and orientation required by the layout rather than cutting a standard straight length to form the corner.

Gutter sizes: 100x76mm, 125x100mm, 150x100mm and 200x150mm. Choose Milled for an uncoated aluminium finish, or one of the 11 listed RAL powder-coated colours to coordinate with your roofline.

Use with the same size of moulded ogee Fast-Fit gutter and the matching jointing components. Check the corner orientation against your plan before ordering.

The AGD Signature Range moulded ogee Fast-Fit aluminium gutter collects rainwater along the roof edge and carries it towards the outlets. Matching corners, outlets and end fittings allow the run to follow the shape of the building.

The shaped ogee front gives the roofline a more decorative appearance. The gutter lengths are made from extruded aluminium and suit both refurbishment and new-build projects.

Gutter sizes: 100x76mm, 125x100mm, 150x100mm and 200x150mm. Length options: 0.5m, 1m, 2m, 2.5m and 3m. Choose Milled for an uncoated aluminium finish, or one of the 11 listed RAL powder-coated colours to coordinate with your roofline.

The moulded ogee system can be supported on matching fascia brackets or directly fixed through the back, following the installation guidance. Use the correct jointing components and sealant, and allow for thermal movement in accordance with the system instructions.

The AGD Signature Range deep flow Fast-Fit jointing clip connects adjoining sections of the matching gutter system. It forms part of the joint assembly between lengths and compatible fittings.

The clip follows the deep flow Fast-Fit section to provide the appropriate joint interface. Use it with the specified sealant and joint preparation method for this system.

Gutter size: 125x100mm. Choose Milled for an uncoated aluminium finish, or one of the 11 listed RAL powder-coated colours to coordinate with your roofline.

Match the clip to the gutter size and jointing arrangement. Follow the profile-specific instructions for assembly and expansion allowance; a clip alone does not replace the required sealing work.

The AGD Signature Range deep flow Fast-Fit rafter bracket provides a support option where the gutter needs to be mounted from the rafters. It is useful where a fascia fixing arrangement is unsuitable.

Select Top Fix for fixing from above or Side Fix for attachment to the side of the rafter. Choose the version that suits the accessible fixing face and the required gutter position.

Gutter size: 125x100mm. Choose Milled for an uncoated aluminium finish, or one of the 11 listed RAL powder-coated colours to coordinate with your roofline.

Match the bracket to the deep flow Fast-Fit gutter size. Check the rafter arrangement, roof edge clearance and required fixing positions before ordering.

The AGD Signature Range deep flow Fast-Fit fascia bracket supports the matching gutter from the fascia board. Its profile follows the gutter section to keep the run securely positioned beneath the roof edge.

Choose the bracket size to match the deep flow Fast-Fit gutter. Suitable support positions help maintain the intended alignment and fall along the installation.

Gutter size: 125x100mm. Choose Milled for an uncoated aluminium finish, or one of the 11 listed RAL powder-coated colours to coordinate with your roofline.

Use fixings appropriate for the fascia and follow the profile-specific installation guidance for bracket spacing and support around fittings.

The AGD Signature Range deep flow Fast-Fit stop end closes an open end of the gutter run. It provides the matching terminal fitting where the gutter finishes at the edge of the roofline.

Made for the deep flow Fast-Fit profile, this aluminium component completes the shape of the gutter at the end of the run. Select the size that matches the gutter section.

Gutter size: 125x100mm. Choose Milled for an uncoated aluminium finish, or one of the 11 listed RAL powder-coated colours to coordinate with your roofline.

Fit and seal the stop end in accordance with the system instructions. Check the completed joint as part of the installation's water test.